ANS is committed to advancing, fostering, and promoting the development and application of nuclear sciences and technologies to benefit society.
Explore the many uses for nuclear science and its impact on energy, the environment, healthcare, food, and more.
Division Spotlight
Decommissioning & Environmental Sciences
The mission of the Decommissioning and Environmental Sciences (DES) Division is to promote the development and use of those skills and technologies associated with the use of nuclear energy and the optimal management and stewardship of the environment, sustainable development, decommissioning, remediation, reutilization, and long-term surveillance and maintenance of nuclear-related installations, and sites. The target audience for this effort is the membership of the Division, the Society, and the public at large.
Meeting Spotlight
2024 ANS Annual Conference
June 16–19, 2024
Las Vegas, NV|Mandalay Bay Resort and Casino
Standards Program
The Standards Committee is responsible for the development and maintenance of voluntary consensus standards that address the design, analysis, and operation of components, systems, and facilities related to the application of nuclear science and technology. Find out What’s New, check out the Standards Store, or Get Involved today!
Latest Magazine Issues
Mar 2024
Jan 2024
Latest Journal Issues
Nuclear Science and Engineering
April 2024
Nuclear Technology
Fusion Science and Technology
February 2024
Latest News
Can hydrogen be the transportation fuel in an otherwise nuclear economy?
Let’s face it: The global economy should be powered primarily by nuclear power. And it probably will by the end of this century, with a still-significant assist from renewables and hydro. Once nuclear systems are dominant, the costs come down to where gas is now; and when carbon emissions are reduced to a small portion of their present state, it will become obvious that most other sources are only good in niche settings. I mean, why use small modular reactors to load-follow when they can just produce that power instead of buffering it?
Satoshi Suzuki, Kazuyoshi Sato, Masanori Araki, Kazuyuki Nakamura, Masayuki Dairaku, Kenji Yokoyama, Masato Akiba
Fusion Science and Technology | Volume 30 | Number 3 | December 1996 | Pages 793-797
Plasma-Facing Components: Analysis and Technology | doi.org/10.13182/FST96-A11963033
Articles are hosted by Taylor and Francis Online.
Since the thermal loads causes deformation of the divertor plate, it is one of the critical issues to develop support structures which can suppress the deformation within an allowable tolerance. Slide support structures and rigid support structures have been proposed for the ITER divertor plate design. Advantage of the fully rigid support structure is 1) the thermal deformation can almost fully be suppressed, 2) the fabrication process becomes simpler than the slide support structures. However, stresses/strains of the divertor plate with the rigid support structure are seemed to be much higher than those of the slide support structures. To evaluate the thermal fatigue behavior for the rigid support structure, the authors have developed a 1 m long divertor mock-up and have performed the thermal cycling experiments of the mock-up. The mock-up consists of 36 armor tiles, a soft copper (OFHC-Cu) heat sink, and an OFHC-Cu cooling tube. The armor tiles were made of a unidirectional Carbon Fiber Reinforced Carbon composite material which has high thermal conductivity perpendicular to the coolant flow direction. The saddle-shaped armor tiles were brazed onto the heat sink with a silver braze. The thermal cycling experiment was performed in an area of 25 × 50 mm2 at an incident heat flux of 25 MW/m2 for a pulse duration of 10 s. As a result, a water leakage from the cooling tube between the heated armor tiles occurred at 1247th thermal cycle. In the scanning electron microscope (SEM) observation, the striation which is typical for fatigue cracking was clearly observed at the fracture surface of the cooling tube. The 3-D finite element analysis for the simulation of the experiment was also performed, and the large strain amplitude was found at the heated side of the cooling tube. Therefore, the fatigue cracking of the cooling tube could mainly be attributable to this large strain amplitude. To realize the rigid support structure, more stiffness is required for the structural material of the cooling tube.