ANS is committed to advancing, fostering, and promoting the development and application of nuclear sciences and technologies to benefit society.
Explore the many uses for nuclear science and its impact on energy, the environment, healthcare, food, and more.
Division Spotlight
Fuel Cycle & Waste Management
Devoted to all aspects of the nuclear fuel cycle including waste management, worldwide. Division specific areas of interest and involvement include uranium conversion and enrichment; fuel fabrication, management (in-core and ex-core) and recycle; transportation; safeguards; high-level, low-level and mixed waste management and disposal; public policy and program management; decontamination and decommissioning environmental restoration; and excess weapons materials disposition.
Meeting Spotlight
2024 ANS Annual Conference
June 16–19, 2024
Las Vegas, NV|Mandalay Bay Resort and Casino
Standards Program
The Standards Committee is responsible for the development and maintenance of voluntary consensus standards that address the design, analysis, and operation of components, systems, and facilities related to the application of nuclear science and technology. Find out What’s New, check out the Standards Store, or Get Involved today!
Latest Magazine Issues
Apr 2024
Jan 2024
Latest Journal Issues
Nuclear Science and Engineering
May 2024
Nuclear Technology
Fusion Science and Technology
Latest News
X-energy receives federal tax credit for TRISO fuel facility
Advanced reactor company X-energy has been awarded $148.5 million in tax credits under the Inflation Reduction Act for construction of its TRISO-X fuel fabrication facility in Oak Ridge, Tenn.
Ronald D. Boyd
Fusion Science and Technology | Volume 13 | Number 4 | May 1988 | Pages 644-653
Technical Paper | Blanket Engineering | doi.org/10.13182/FST88-A25139
Articles are hosted by Taylor and Francis Online.
A quasi-automated high heat flux flow boiling facility has been developed for the systematic study of critical heat flux (CHF), heat transfer, and two-phase pressure drop. High heat flux research is important in state-of-the-art electronics and fusion component design. For fusion applications, there are practically no low-pressure data for large values of coolant channel length-to-diameter (L/D) ratio (i.e., 100), channel diameters near 1.0 cm, and medium to high heat flux levels (i.e., 100 to 2000 W/cm2). A second step is provided to fill this void. Forced flow boiling (with water) quasi-steady experiments have been conducted on uniformly (resistively) heated horizontal copper tubes. The tubes were 1.02 cm in inside diameter and 117.87 cm long. The inlet water temperature was 20°C. For a 1.6-MPa exit pressure, measurements of the CHF varied from the annular flow regime (150 W/cm2) to the subcooled flow boiling regime (425 W/cm2). The mass velocity was varied from 0.63 to 3.5 Mg/m2·s. At 1.6 MPa, the transition between the annular and subcooled CHF regimes was measured to occur between 1.03 and 1.26 Mg/m2·s. Large axial variations in the Nusselt number were also measured. For example, at 1.7 Mg/m2·s, the Nusselt number varied from 120 at the channel's entrance to 500 at the exit. The CHF data were compared with correlations developed by Bowring, Katto, and Merilo. Below 4.0 Mg/m2, all correlations overpredicted the CHF data. Merilo's correlation, which was developed for high-pressure horizontal flows, predicted the CHF significantly above the present low-pressure data. The effects of orientation on the CHF data were small. Visual observations of the outside of the test section showed that burnout occurred simultaneously around the test section's perimeter. Circumferential measurements of the outside wall temperature also showed negligible variations. Therefore, at low pressures, the following conditions reduced the effect of orientation: 1. high liquid Reynolds number 2. high inlet subcooling 3. moderate L/D 4. increased effects of surface tension relative to buoyant and viscous forces at higher pressures (i.e., low Bond and Ohnesorge numbers)5. low value of buoyant forces relative to inertia forces.